Iti fitter multiple choice questions gauges chapter

Iti fitter multiple choice questions gauges chapter


Iti fitter multiple choice questions gauges chapter important questions with answers For all types iti fitter competitive exams


1. Which one of the following instruments is used for checking large internal diameter

(a) small hole gauge     (b) telescopic gauge     (c) pluge gauge      (d) snap gauge

(b) telescopic gauge

2. A taper ring gauge is used for checking

(a) external taper     (b) internal taper     (c) external threads     (d) internal threads

(a) external taper

3. Thread ring gauge is used for checking

(a) external threads     (b) internal threads     (c) external diameter of cylindrical job     (d) internal diameter of jobs

(a) external threads

4. Gauges are made of

(a) mild steel    (b) alloy steel     (c) cast steel   (d) cast iron 

(c) alloy steel

5. Taper plug gauge is used for checking

(a) taper holes     (b) external diameter of cylindrical parts     (c) internal diameter of cylindrical parts    (d) diameter of straight holes

(a) taper holes


Iti fitter multiple choice questions gauges chapter important questions with answers For all types iti fitter govt exams


6. A plain ring gauge is used for checking

(a) taper holes     (b) external diameter of cylindrical parts     (c) internal diameter of cylindrical parts     (d) major diameter of external threads

(b) external diameter of cylindrical parts

7. A plug gauge which has its "Go" and "No Go" sizes on the same end is known as

(a) single ended plug gauge     (b) double ended plug gauge     (c) progressive plug gauge     (d) continues plug gauge

(c) progressive plug gauge

8. Which one of the following gauges is used to align the lathe tool with the work

(a) try square     (b) centre gauge     (c) thread gauge     (d) straight edge

(b) centre gauge

9. Which one of the following gauges is used to check the threading tool of lathe for accuracy on the 60° angle

(a) screw pitch gauge     (b) thread plug gauge     (c) centre gauge     (d) thread ring gauge

(c) centre gauge


iti fitter previous question paper


10. Centre gauge is used for

(a) chec the profile of thread   (b)  checking the fit of thread    (c) checking the pitch of the thread     (d) set lathe tool at correct centre height  

(d) set lathe tool at correct centre height

11. A feeler gauge is used for

(a) adjusting the parts for play     (b) checking gap between matting part     (c) checking radii of jobs     (d) cheking accuracy of holes

(b) checking gap between matting part

12. Clearance between matting part is measured by

(a) caliper gauge   (b) feeler gauge     (c) "Go" gauge     (d) dial gauge  

(b) feeler gauge

13. In an adjustable snap gauge, two adjustable jaws are provided on

(a) both sides     (b) one side     (c) one in each side     (d) none of the above

(b) one side

14. Which one of the following grade of gauge is used for checking the parts made by an operator in the workshop

(a) workshop gauge     (b) inspection gauge     (c) reference gauge     (d) none of the above

(a) workshop gauge

15. Which one of the following gauge is used for checking cylinder, which are not kept in vertical or horizontal position

(a) pilot gauge   (b) snap gauge   (c) ring gauge       (d) plug gauge  

(a) pilot gauge


iti fitter jobs in railway 


16. In a taper plug gauge the "Go" and "No Go" size are denoted by a step on

(a) the same side     (b) the either side     (c) the both sides     (d) separately

(a) the same side

17. Fixed type snap gauge have "Go" and "No Go" ends

(a) the same side     (b) the either side     (c) the both sides     (d) separately

(a) the same side

18. At what standards temperature are the gauge kept in the section

(a) 10°C     (b) 20°C     (c) 10°F     (d) 20°F

(b) 20°C

20. "Go" side of the plug gauge will have the diameter equal to

(a) actual size of the job     (b) basic size of the job     (c) minimum size of the job     (d) maximum size of the job

(c) minimum size of the job


iti fitter jobs in govt


21. For general use in workshop slip gauge of which grade are used

(a) grade - 0     (b) grade - 1     (c) grade - 2     (d) none of the above

(c) grade - 2

22. The accuracy of reference gauge is

(a) 0.05mm     (b) 0.01mm     (c) 0.001mm     (d) 0.0001mm

(c) 0.001mm

23. As per Indian standards a special set of slip gauge is used consisting of

(a) 81 pieces     (b) 112 pieces     (c) 120 pieces     (d) 130 pieces

(b) 112 pieces

24. Grade-1 slip gauges are used in

(a) workshop by operator     (b) inspection room     (c) either 'a' or 'b'     (d) neither 'a' nor 'b'

(b) inspection room

25. Hardness of slip gauges should be

(a) more than 63 HRC  (b) 58 HRC     (c) 55 HRC     (d) 50 HRC

(a) more than 63 HRC

"Iti fitter multiple choice questions gauge chapter important questions with answers we try add more question so please stay with us" 


Read - Iti fitter multiple choice questions marking and marking tools chapter click here 



About Author:


My name is Gokul Bairagi and I am a student and I realized that if qualifying any competitive exams then, mainly required theory knowledge. So I am trying my best to serve you with the best information in the easiest way. That can help everyone to get a better career

Let's Get Connected: .. |.. ..|..


Post a Comment

0 Comments